PLC with DI 10*DC24V. DO 8*relays, 2*AI, 2*AO, 1*RS232, 1*RS485 Programmable Logic Controller pump control

 Technical Specifications CPU Main parameter of electrical sourceI/O10-CH 24VDC input8-CH Relay output2-CH AI1-CH AOSupply Voltage220VAC @50Hz Expansion capabilityUp to 10 modules can be extended Allowance range187~264VAC @50Hz Storage capacityProgram area : 120KBMaximum current120mA N Area : 8KB M Area

Featured Products


PLC with DI 10*DC24V. DO 8*relays, 2*AI, 2*AO, 1*RS232, 1*RS485 Programmable Logic Controller pump control

 

Technical Specifications


 
CPU Main parameter of electrical source
I/O
10-CH 24VDC input
8-CH Relay output
2-CH AI
1-CH AO
Supply Voltage
220VAC @50Hz
Expansion capabilityUp to 10 modules can be extended Allowance range
187~264VAC @50Hz
Storage capacityProgram area : 120KBMaximum current
120mA
N Area : 8KB 
M Area : 5KB
Output Voltage
24VDC
Power loss holding area : 2KBOutput  Current
400mA
TimerHardware timing : 1,
0.1ms ~ 500ms
No limit on software timing (min. 1ms)
Short-circuit protection
800mA,24VDC output
Counter16bitCommunication interface1*RS232,
Operating rate
0.06μ s(Boolean operation instruction)
1*RS485
Interrupt input
4
Communication protocolMODBUS RTU protocol,
Analog potentiometer
2 ,0~255
Custom protocol
24VDC Input ChannalRelay Output Channal
Type of inputP/M-lesendType of outputRelay
Input signalRated voltage 24VDCOutput signalRated voltage 24VDC
or 24 ~ 230VAC
0 ~ 30V DC5 ~30VDC
or 5 ~ 250VDC
Input signal (ON)15~30VDC and
> 3 mA
Common terminal output current summation< 5A
Input signal (OFF)0~5VDC and
< 1mA
Output contact capacity2A, Impedance load
Input delay< 0.6ms (Rated input voltage)Switch delay< 10ms
Isolation methodOptoelectronic isolationThe isolation voltage between the coil and the contact3000V AC, 1min, leak current 1mA
Isolation of pressure1000VDCIsolation voltage between contacts750V AC, 1min, leak current 1mA
Mechanical life of relayWithout load, it can reach more than 10,000,000 times;
Rated resistance 2A load, up to more than 100,000 times
AI ChannalAO Channal
    
    
    
    
    
    
    
Dimensions and MountingWork Environment
Dimensions
120mm(L)×80mm(W)×63mm(H)
Operating temperature0 ~ +55ºC
Weight
380g
Storage temperature-40 ~ +70ºC
Way to install35mm DIN railRelative humnidity5% ~ 95% Noncondensing
Panel mounting type



Main interface and terminal definitions

PLC with DI 10*DC24V. DO 8*relays, 2*AI, 2*AO, 1*RS232, 1*RS485 Programmable Logic Controller pump control

1.Indicator lights: RUN, COM and ERR are used to display module operation, communication and fault conditions respectively, I and Q are used to show the module operation, communication and fault conditions respectively. Indicates the input and output status of each channel.
2.Module output terminal: It is composed of power supply driver 1L, 2L and output point Q. "*" indicates that there is no actual output on this channel. Physical connection, with relay output at the terminal.
3. Module input terminals: consisting of common terminal 1M, 2M and input point I. Source/drain type connection can be used.
4. RS232 communication interface: This interface can be used for program download, communication with touch screen and host computer. MODBUS RTU/free protocol.
5. RS485 communication interface: This interface can be used to communicate with touch screen, upper computer, third-party instruments, etc., and supports MODBUS RTU/free protocol.
6. Power supply of the module: L, N, AC220V power supply's fire wire, zero wire and protective ground terminal.
7. 24VDC power supply external to the module: VO+ and VO- are 24VDC positive and negative terminal blocks respectively.

Note: PCS1200 programmable logic controller terminals are all pluggable.



Terminal tag definition specification
 
TerminalTerminal instructionsTerminalTerminal instructions
485+The positive pole of the  RS485 interface
RA
A channel current input
485-
The negative pole of the RS485 interface
A+
A channel voltage input
V0Voltage output
M
Analog input common terminal
I0Current output
B+
B channel current input
M0
Analog output common terminal
RB
B channel voltage input
1L
Output common terminal
1M
External input common terminal
Q0.0
Normal Output terminal
I0.0
Normal input terminal
Q0.1
Normal Output terminal
I0.1
Normal input terminal
Q0.2
Normal Output terminal
I0.2
Normal input terminal
Q0.3
Normal Output terminal
I0.3
Normal input terminal
2LOutput common
I0.4
Normal input terminal/External interrupt input
Q0.4Normal Output terminal
I0.5
Normal input terminal/External interrupt input
Q0.5
Normal Output terminal
I1.0
Normal input terminal
Q0.6
Normal Output terminal
I1.1
Normal input terminal
Q0.7
Normal Output terminal
I1.2
Normal input terminal
GNDGND
I1.3
Normal input terminal
N
Zero line
VO-
External power supply :positive
L
Fire line
VO+
External power supply :negative

Input channel connection mode

PLC with DI 10*DC24V. DO 8*relays, 2*AI, 2*AO, 1*RS232, 1*RS485 Programmable Logic Controller pump control




Output channel connection mode

PLC with DI 10*DC24V. DO 8*relays, 2*AI, 2*AO, 1*RS232, 1*RS485 Programmable Logic Controller pump control


RS232 communication port definition
 
PIN123456789
Definition--
RXD
TXD
--
GND
--user-defineduser-defined--





About CHINT

Founded in 1984, the Chint Group provides safe, reliable and stable industrial electrical equipment and solutions for energy efficient management systems. With 30 years of development it has grown to be Asia' s largest low*voltage electrical product supplier and is the leading brand of the whole industry chain in industrial electric in Asia. With three R&D centers located in Europe, North America and China, there are also branches in over 20 countries and more than 30.000 employees in the world. CHINT provides reliable products, system solutions and services to more than 100 countries worldwide.


PLC with DI 10*DC24V. DO 8*relays, 2*AI, 2*AO, 1*RS232, 1*RS485 Programmable Logic Controller pump control



•    3 Global Research Centers: Europe, North America, Asia Pacific
•    6 International Marketing & Sales Area: Asia Pacific, Middle East and Africa, Europe, Latin America, North America, China
•    9 Manufacturing Bases: China (Wenzhou, Shanghai, Hangzhou, Jiaxing, Xianyang, Jiuquan), Thailand, Egypt, Germany
•    22 Logistics Centers 14 International Subsidiaries 17 Marketing Offices in China 2300 Sales Companies


About Chitic

Chrtic Control Engineering Co.. Ltd. is a subsidiary company of Chint, and a leading provider of automation & control technologies and applications in China that helps the industry customers to improve operating safety, reliability and efficiency. Chitic has series of products including PCS1800 DCS, TDCS9200 DCS and CTS700 DCS, information platform for water company, control system for high speed rapier loom, drive system of switched reluctance motor, solar energy monitoring system, computing cloud center for new energy; etc. Chitic control system won 2006 National Science and Technology Progress Awards of China, CTS700 DCS won the award of 2010 Innovative Product of China. Chitic headquarter is located at the beautiful city of Hangzhou, two hours drive from Shanghai. Chitic has its own science & technology park, Chitic Park, which covers about six thousand square meters.

Our Business Sector
PLC with DI 10*DC24V. DO 8*relays, 2*AI, 2*AO, 1*RS232, 1*RS485 Programmable Logic Controller pump control





Typical Reference
PLC with DI 10*DC24V. DO 8*relays, 2*AI, 2*AO, 1*RS232, 1*RS485 Programmable Logic Controller pump control




PLC with DI 10*DC24V. DO 8*relays, 2*AI, 2*AO, 1*RS232, 1*RS485 Programmable Logic Controller pump control
 

Contact us

Please feel free to give your inquiry in the form below We will reply you in 24 hours